Measuring windows correctly starts with choosing a mount. Inside-mount blinds sit within the window frame and need precise width and height readings taken at three points, recorded to the nearest 1/8 inch. Outside-mount blinds cover the frame and need about 3 inches added to each side and above. A steel tape measure and clear notes prevent costly reorders.

Homes in Brandon, FL, get strong sun for most of the year. The U.S. Department of Energy estimates that about 76% of the sunlight hitting standard double-pane windows enters the home as heat. Properly fitted window shades and blinds block more of that heat and close light gaps. A fit that is off by just 1/4 inch can leave visible gaps or cause a blind to rub against the frame.

 

Inside Mount vs. Outside Mount and How Each One Fits

The mount style decides where window shades and blinds attach and which measurements matter most. An inside mount installs within the window casing for a clean, built-in look that shows off decorative trim. An outside mount attaches to the wall or trim above the window and overlaps the opening, which makes the window look larger and blocks more light around the edges.

Feature Inside Mount Outside Mount

Appearance Clean, built-in, shows trim Frames the window, can make it look larger

Light control Small side gaps of about 1/4 inch Overlap reduces light leaks

Frame depth

needed Usually 1.5 to 3 inches Little to none

Best for Square frames with attractive molding Shallow, uneven, or out-of-square frames

Measurement

focus Exact opening size Area to cover plus overlap

 

Outside mounts are a strong choice for bedrooms that need darkness for daytime sleep and for older homes where window frames have shifted over time.

 

What Should Be Checked Before Measuring a Window?

Accurate measurements depend on the right tools and a few quick checks of the window frame. With everything ready, measuring takes about 5 to 10 minutes per window.

l Steel tape measure: A metal tape stays straight, while cloth tapes stretch and can add 1/4 inch or more of error.

l Pencil and notepad: Labeling each window, such as “Kitchen Left,” prevents mix-ups when ordering several sizes.

l Step stool: A stable stool allows straight readings at the top of tall windows.

l Frame depth check: Measuring from the glass to the front edge of the frame confirms whether an inside mount will fit.

l Obstruction check: Window cranks, alarm sensors, and locks can block headrails or slats.

l Square check: Comparing the two diagonal measurements shows whether the frame is square, and a difference greater than 1/4 inch often points toward an outside mount.

 

Measuring Inside-Mount Blinds and Shades Step by Step

Inside-mount measurements must be exact because window shades and blinds in this style sit within the frame with very little clearance. Manufacturers typically deduct about 1/4 to 1/2 inch from the width so the product fits without scraping.

1. Measure the inside width at the top, middle, and bottom of the opening.

2. Record the narrowest of the three widths to the nearest 1/8 inch.

3. Measure the inside height at the left, center, and right, from the top of the opening to the sill.

4. Record the longest of the three heights so the product reaches the sill everywhere.

5. Measure the frame depth and compare it with the minimum depth listed for the chosen product.

6. Write width first, then height (for example, 34 3/8" W x 60 1/2" H), and avoid subtracting any extra space, since the factory handles deductions.

 

Measuring Outside-Mount Blinds and Shades Step by Step

Outside-mount measurements focus on the area to cover rather than the opening itself. Window shades and blinds on outside mounts are built to the exact size ordered with no factory deductions, so the final numbers should match the full size wanted on the wall.

1. Measure the width of the opening or the outer edges of the trim.

2. Add 1.5 to 3 inches to each side, for a total of 3 to 6 inches, to limit light leaks.

3. Measure height from the mounting point, usually 2 to 3 inches above the opening, down to the sill or about 2 inches below the opening.

4. Confirm the mounting surface is flat and at least 2 inches tall to hold the brackets.

5. Check clearance for door handles, light switches, and nearby walls before finalizing the width.

 

Which Measuring Mistakes Lead to Costly Reorders?

Most sizing problems come from a handful of repeat errors, and custom window coverings usually cannot be returned once they are cut to size.

l Rounding to the nearest inch: Custom products are built in 1/8-inch increments, so rounding can create gaps or a blind that will not fit.

l Measuring one point only: Older frames are rarely perfectly straight, and a single reading can miss a narrower spot.

l Ignoring frame depth: A shallow frame can leave an inside-mount headrail sticking out past the trim.

l Reversing width and height: Swapping the order on a 36 x 48 window produces a 48 x 36 product.

l Assuming matching windows are identical: Two windows that look the same can differ by 1/4 inch or more.

A Final Checklist Before Ordering

l Every window is labeled by room and position.

l Each measurement is recorded to the nearest 1/8 inch, with width listed first.

l Inside-mount windows have three widths, three heights, and a depth reading.

l Outside-mount windows include overlap and confirmed bracket space.

l Obstructions and diagonal measurements are noted for each window.

 

Key Takeaways for a Perfect Fit

Choosing the right mount, using a steel tape, and recording every number to the nearest 1/8 inch are the habits that separate a precise fit from an expensive reorder. Before ordering, it helps to ask a few practical questions. Does the frame have enough depth for an inside mount? Would extra overlap keep a bedroom darker in the afternoon? Will the new coverings need to work alongside curtains or a motorized system?

A proper fit also pays off in comfort. The U.S. Department of Energy reports that heat gain and loss through windows accounts for 25% to 30% of residential heating and cooling energy use, so well-measured window shades and blinds help keep Florida cooling costs under control.

Not everyone wants to spend a Saturday on a step stool with a tape measure, and that is where Budget Blinds of Brandon comes in. From its location in Tampa, FL, the team serves homeowners throughout Brandon, FL, with professional measuring, product guidance, and installation for window shades and blinds of every style. A free in-home consultation brings samples and expert measurements right to the door, so every blind and shade arrives sized right the first time. Book a consultation today and let the professionals handle the numbers.

 

FAQs

Are roller shades measured the same way as other blinds?

The steps are largely the same, with width and height taken at three points and recorded to the nearest 1/8 inch. Inside-mount roller shades leave a slightly larger side

gap, often 1/4 to 1/2 inch per side, because of the roller and brackets. For blackout fabric in a bedroom, an outside mount with 2 to 3 inches of overlap on each side does a better job of stopping light leaks.

 

What should I do if my window opening is uneven?

Measure the width at the top, middle, and bottom and use the narrowest reading so the product does not bind. If the diagonals differ by more than 1/4 inch or the widths vary by more than 1/2 inch, an outside mount is usually the better choice because it covers the irregular frame and hides the uneven edges.

 

How do I plan measurements when pairing shades with curtains?

Shades work best as an inside mount when curtains will hang in front, leaving the wall space free for the curtain rod. A common approach places the rod 4 to 6 inches above the frame and extends it 8 to 12 inches past each side. If the shade is an outside mount, check that the curtain rod brackets project far enough to clear the shade’s headrail.

 

Do motorized blinds need extra measuring considerations?

Yes. Motor housings can require more frame depth than manual versions, so the depth measurement should be compared with the product’s specifications. It also helps to note the location of the nearest outlet, plan for battery or solar options, and confirm there is room for a remote wall switch or charging access.

 

Should I measure windows before or after renovation work?

Final measurements should be taken after any work that affects the window opening is complete, including new trim, tile, drywall, or replacement windows. Even a new layer of trim or paint can change an opening by 1/8 inch or more. Early measurements are useful for budgeting, but orders should be based on the finished frame.

UPGRADE YOUR WINDOWS NOW

Get the custom blinds, shades, or shutters you want today with flexible payment options available.


See your payment options during your free consultation*

Call Us Today at (813) 445-7121

How did you hear about Budget Blinds?

(select all that apply)